Shower Consumer Unit Wiring | on ElectriciansForums
2017年11月12日 · Find Shower Consumer Unit Wiring Advice and Help. How-to Shower Consumer Unit Wiring in the DIY Electrical Advice advice boards on ElectriciansForums.net Est.2006 | Free Electrical Advice Forum. Shower Consumer Unit Wiring on ElectriciansForums.net Electrical Advice Forum.
wire up shower to consumer unit | DIYnot Forums
2005年2月12日 · I am planning to have a single 10mmsquare cable from the 45A mcb in box to the shower, with the big red switch cut into the cable halfway along, outside the bathroom door. The switch just says L & N Supply, L & N Load, plus the earth, so I would connect the load side to shower and supply side to box, and earth the switch back to the consumer unit.
connecting a shower consumer unit. | DIYnot Forums
2005年1月13日 · Used a 30 mA RCD between the 40 A MCB in the consumer unit (I was limited to this as this was the maximum current MCB that was available for my consumer unit) and the DP swicth in the bathroom. The RCD was part of a shower consumer unit which also incorporated a 63 amp MCB. It was cheaper to buy one of these than the 30 mA RCD on its own.
Consumer unit wiring for 10.8kW shower | DIYnot Forums
2015年7月29日 · Have made the run from the shower-room isolator using 10mm2 cable, now working out the best way to wire it in to the consumer unit. It's a Memera 2000 AD and the layout is a 100A main isolator with 6 6A MCB lighting circuits directly off it, then a 80A RCD protected second section with 3 32A MCB circuits (two socket rings and a cooker).
powering a shower consumer unit | DIYnot Forums
2004年9月21日 · I have fitted a 9.5kw shower, wired with 10.0mm cable, switched with 50A pull switch, connected to a sperate shower (63A 30mA RCD, with a spare 50A Type B MCB) consumer unit. My problem is where do i source the power for this new consumer unit and will i need to use 16.0mm cable or will 10.0mm...
Earth bonding to consumer unit | DIYnot Forums
2017年1月23日 · The metallic pipe of the shower should be supplementary bonded to the earth terminal of the shower. This cable would normally be 4mm2CSA. There is no need to terminate between shower and CU (consumer Unit) as the supply cable to the shower should have a CPC (Circuit Protective Conductors/AKA earth) that serves that purpose.
Changing a fuse on the consumer unit - DIYnot
The three most common are the single bladed and double bladed fuse wire carriers, and the cartridge fuse. Fuse Wire. The picture shows a typical cartridge fuse. First ensure the consumer unit is switched off. The fuse wire is held in place by …
House consumer unit to garage consumer unit - on …
2019年5月23日 · Hi all I’m planning to install a consumer unit in my garage. The unit will eventually power a 32amp hot tub, 2 double sockets and a small lighting circuit. The unit will eventually power a 32amp hot tub, 2 double sockets and a small lighting circuit.
How to install a second consumer unit | DIYnot Forums
2003年11月9日 · How is the spark going to connect this up? my current supply set up is as follows: The supply comes into the house via a 60A tamper proof fuse, then through the meter to the existing consumer unit (Rated at 100A max), although it could never draw more than 60A else the main fuse would blow i guess? The existing Unit has the following MCB's ...
Adding an rcbo into a consumer unit. | DIYnot Forums
2019年7月15日 · I have a (yes, currently very messy) consumer unit. It's a standard BG dual RCD unit. I want to put a single rcbo in for an electric shower. If you look at the picture there's a busbar across the 6 rcbs to the RCD in each case. I want to put in an rcbo. I think I …