REPAIR of a Code 41... - Polaris ATV Forum
2011年8月2日 · Could this be why I am getting the code 41? Also removed fuel injector, and T-MAP sensor, all good. Cleaned the throttle body, and replaced the air filter with a UNI.
I keep getting code 41! - PRC Polaris Ranger Club
2012年11月2日 · Its very rare for a 41 code to be the actual sensor. Its usually the Tbap harness. There may be dirt on the mass air flow sensor in the intake. make sure the air cleaner is clean. the sensor may be sensing not enough or to much air and adjusting the fuel accordingly. making it run to rich or to lean. just a thought.
Code 41 and throttle bog down | Polaris Ranger Forum
2019年10月3日 · I've been getting throttle bog down, and I didn't quite know where to start. I found a discussion about the TBap sensor wiring. And I'm wondering if this might be causing this throttle bog down symptom. I have a constant code 41, and I noticed the code before the new symptom. WHERE do the wires typically fail? Do any of you have any words on this.
Codes 41 and 46 - PRC Polaris Ranger Club
2010年7月4日 · Decided to stop by the brand new Polaris dealer south of town on the way home to discuss the codes, etc. They confirmed problem and they are going to install the repair harness under warranty even though my Ranger was out of warranty by about 40 days.
error code 41 - PRC Polaris Ranger Club
2013年6月2日 · The wires usually fail close to the connector head, some times within the head and some times 6-8 inches away from the connector due to Polaris putting a wire protective sleeve over the wires and drawing down too tight with plastic ties that leads to eventually the tie wearing into the harness.
2008 Polaris Ranger Crew Air Intake Sensor Code 41 Repair
http://www.BigKidReviews.com Code 41 on my 2008 Polaris Ranger Crew 700 twin. That is a Intake Air Sensor. But after reading several posts across the net, ...
Polaris diagnostic codes 41 & or 45..Broken T-Bap wiring
2012年2月15日 · 1. Turn the key switch on and off 3 times leaving it on the 3rd time. This puts the ECU into diagnostic mode. If codes are present their numbers will be displayed on the instrument cluster. When all codes have been displayed "End" will appear on the cluster. 2. Remove the seat and locate the sensor on the air intake tube.
Polaris Ranger Check Engine Codes: An Essential Guide
2023年8月9日 · These codes (41: Air Temp Sensor, 42: Engine Temp Sensor, 43: TPS 1, 45: Barometric Pressure Sensor) would alert you of failing or disconnected sensors. Lack of signals from these critical sensors can cause erratic engine behavior. Checking the connectors and wires leading to these specific sensors should be your first step.
Checking Diagnostic Trouble Codes (DTC) | Polaris ATV Forum
2012年5月18日 · The codes are in two-digit numbers, so the previous sequence would be 12, 41, and 61. 12 = start and 61 = end. 12 may or may not happen. This is a general list of codes. Different models and years may have slight variations. To erase a code, remove the negative battery cable for 30 seconds.
2009 Ranger 500EFI engine codes 22, 41, 42, 44, 45, 46...
2017年3月9日 · My 2009 Ranger 500 EFI 4x4 shows codes 22, 41, 42, 44, 45, 46, 47, 58, 74. Which is freakin ridiculous! -Pulled apart all wiring harnesses and traced wiring from MAP sensor and TPS, no opens or shorts from sensors to computer or noticeable damage. -The maint light is NOT on while running. It blinks quick when starting then goes out.