Wipe on poly over danish oil (or tung oil)? - Sawmill Creek
2008年3月26日 · As far as the leafs touching, after poly dries, new poly doesn't want to stick to it without the previous coat being roughed up, so you should be fine with two dried polyed pieces touching. Make sure you use a real drying poly, not some goofy oil-poly blend that never dries.
wipe on poly over danish oil sticky - Sawmill Creek
2019年9月30日 · I am working on a small white oak counter top. I put on 1 coat of watco dark walnut danish oil on just the top. 4 days later a coat of minwax wipe on poly on both sides. 30 hours later the poly and danish oil side are sill sticky. The underside with no danish oil dried fine. take it I just not wait long enough for the danish oil to dry.
Waterbase Poly over Watco Danish Oil? - sawmillcreek.org
2021年3月1日 · It will work if you wait long enough for the Danish oil to cure; several days at least. It would be better, however, if you spray a coat of dewaxed shellac over the Danish oil. But you should make some samples as you may find out that just the dewaxed shellac gives you all the grain enhancement you were looking for from the Danish oil.
Water based Poly over Danish Oil - Sawmill Creek
2005年5月21日 · My jewerly box is getting close to finish. I just put two coats of danish oil on it, but i am not happy with the sheen. I would like a little more shine to it. I was thinking about a couple coats of poly, but I would prefer to use a water based polt to avoid any yellowing or discoloration. It is Ok to put a water base top-coat over an oil based ...
Poly/Varnish Over Watco Danish Oil - Sawmill Creek
2010年11月19日 · But yes, you can apply a wiping varnish (either poly or alkyd) over the danish oil. I'd test either though to make sure you have zero adhesion probs; poly is notorious for this. 11-20-2010, 9:29 PM #3
Can I put WO Poly on top of Watco Danish Oil? - sawmillcreek.org
2011年9月10日 · You absolutely can put poly over dainsh oil. The results will be just like whatever poly your using i.e. gloss/semi-gloss/satin. They are both oil based finished. I usually give the danish oil over night to cure, but I have only waited a few hours before applying the poly with no ill effects. Sanding or scuffing the danish oil is not necessary.
wipe on poly over danish oil sticky - Page 2 - Sawmill Creek
2019年10月26日 · I am working on a small white oak counter top. I put on 1 coat of watco dark walnut danish oil on just the top. 4 days later a coat of minwax wipe on poly on both sides. 30 hours later the poly and danish oil side are sill sticky. The underside with no danish oil dried fine. take it I just not wait long enough for the danish oil to dry.
Lacquer over Danish oil? - sawmillcreek.org
2019年11月11日 · Danish oil is a generic term for a mixture of oil and poly. If concerned about using lacquer, either apply more coats of DO or apply straight poly. Depending on the type of wood it may take 4-5 coats of DO before you start to get a glossy sheen.
Can you use sanding sealer over an oil finish? - Sawmill Creek
2024年1月4日 · Danish oil is a mixture of polyurethane (or another varnish), oil (such as BLO or tung), and a compatible thinner (mineral spirits for poly). The proportions vary, but a 1:1:1 ratio works well. If your preferred sanding sealer is compatible with poly, you should be able to apply it over the Danish oil (assuming the Danish oil has cured).
Oil based stain/Danish Oil - Sawmill Creek
2005年8月16日 · Byron, Watco danish oil is sold with dye built in. They may have the color you want. I think if you used another oil stain first it would seal the wood and prevent the danish oil from penetrating. However, a BIG word of caution if you use an oil finish - red oak pores are hollow, like straws.