Cheaper TTS tool holders? - The Home Shop Machinist
My R8 ATC spindle came in for my Taig, I can now use TTS holders. Ordered a Tormach ER16 holder, but with shipping, pretty expensive for just one tool. Most of my endmills are 1/8th. Maybe I'll make my own holders, setscrew style.
How i designed and made endmill holders for TTS system (2x …
2019年2月23日 · If setup properly TTS(tm) does not register from the collet face. It registers from the face of the spindle nose. It uses a collet that is ground flat on the end and retracts into the spindle nose slightly when the draw bar is tightened. Also a TTS tool holder has a slight recess on the back of the flange just in case.
Cheaper TTS tool holders? - The Home Shop Machinist
2020年9月19日 · Actually as tool holders go (in the grand scheme of all the different tool holders out there) they are one of the cheaper tool holders available. Also quite a wide range from ER16 to ER32, variety of set screw holders, modular tooling, arbors for a variety of applications, and even different TC tappers.
TTS - The Home Shop Machinist & Machinist's Workshop …
2021年2月17日 · TTS in machining usually refers to Tormach Tooling System. I believe they have a trademark on TTS with that meaning. Basically it consists of a 3/4 inch R8 collet that has been face ground so that when clamped on a 3/4 shank tool the face of the collet is slightly above (retracted into) the face of the spindle. The
Tormach style TTS Tooling System... - The Home Shop Machinist ...
2018年1月19日 · The length of the R8 was a problem but i just realised I am already dressing that by servo driving the knee so it can take tool length offsets - this means it should be easier to get a long tool in an R8 adaptor into the spindle. I'll hold fire on the TTS until i have assessed all of these points i think and got the knee driving ok.
Machining Hardened R8 Tool Holder - The Home Shop Machinist …
2023年2月23日 · The picture shows a couple R8 shanks that I would like to convert to the 3/4" TTS type shank similar to the shop-made endmill holder also shown. The R8's being hardened are obviously going to present some problems on the lathe so looking for recommendations. I'm sure that I would probably go thru several carbide inserts
R8 Quick Tool Change System? - The Home Shop Machinist
2020年8月22日 · Anyway, currently I am using Kwik 200, ISO-20 (2 machines), and TTS quick change tooling, and even without an automatic tool changer they save me a LOT of time. Swap the tool and press start. Of course I also have cameras on every machine and video monitors above the computer monitors at my desk.
Power drawbar project (TTS system) - The Home Shop Machinist ...
2016年8月8日 · The power drawbar cylinder I'm going to use is a 4 stage cylinder. This is in order to multiply the force of the cylinder. It will have around 2 tons of force, in fact I'm having problems to fing Belleville washers strong enough. The idea is to make sure I won't have any tool slipeage. My splindle is MT3 so it will clamp the shanks pretty tight.
TTS 9 Degree Long Reach Tool Holder - The Home Shop Machinist ...
2020年4月30日 · Some of you have probably already seen this in the aftermath post. This is not the first tool holder I have made. Its the first long reach tool holder I have made. Its turned from 1144, and reamed to size. Its got a set screw. Not optimum for carbide, but it worked for this job. Its got a 9 degree taper. I made it to machine
Power draw bar verses Mach 1 quick change Tool system
2013年12月14日 · Just give the quill handle a little sharp push to release the tool. The biggest disadvantage would be that you loose z height every time you change a tool as the quill needs to be in the most upright position to release the tool. The tormach tts system looks interesting as well. Just not real crazy about a tool w/in a tool type holder.